Ｄｅｂｉａｎ化したＬＳ−ＧＬがシリアルにはき出すメッセージ よく参照するのでここに載せておきます。 ----------------------------------------------------------------------------- Orion1 CPU = Low === BUFFALO LS-GL U-Boot. === ** LOADER ** ** BUFFALO BOARD: BUFFALO_BOARD_LS_GL LE (CFG_ENV_ADDR=fffff000) U-Boot 1.1.1 (Apr 18 2007 - 18:35:44) Marvell version: 1.12.1 - TINY DRAM CS[0] base 0x00000000 size 128MB DRAM Total size 128MB [256kB@fffc0000] [0kB@f8000000] ## Unknown FLASH at f8000000: Size = 0x00000000 = 0 MB Flash: 256 kB Addresses 20M - 0M are saved for the U-Boot usage. Mem malloc Initialization (20M - 16M): Done Soc: 88F5182 A2 CPU: ARM926 (Rev 0) running @ 400Mhz Orion 1 streaming disabled SysClock = 200Mhz , TClock = 166Mhz USB 0: host mode USB 1: host mode PCI 0: PCI Express Root Complex Interface PCI 1: Conventional PCI, speed = 33000000 Net: egiga0 [PRIME] Using 88E1111 phy Marvell Serial ATA Adapter Integrated Sata device found Device 1: OK Model: Maxtor 6Y080L0 Firm: YAR41BW0 Ser#: Y325DHXE Type: Hard Disk Capacity: 78167.2 MB = 76.3 GB (160086528 x 512) Using device ide0, partition 1 ** Bad partition 1 ** Using device ide1, partition 1 Loading from block device ide device 1, partition 1: Name: hdb1 Type: U-Boot File:/initrd.buffalo 4542614 bytes read Booting from Device 1 hit any key to switch tftp boot. Hit any key to stop autoboot: 0 Hit any key to stop autoboot: 0 Reset IDE: Marvell Serial ATA Adapter Integrated Sata device found Device 1: OK Model: Maxtor 6Y080L0 Firm: YAR41BW0 Ser#: Y325DHXE Type: Hard Disk Capacity: 78167.2 MB = 76.3 GB (160086528 x 512) Using device ide1, partition 1 Loading from block device ide device 1, partition 1: Name: hdb1 Type: U-Boot File:/uImage.buffalo 1828648 bytes read Using device ide1, partition 1 Loading from block device ide device 1, partition 1: Name: hdb1 Type: U-Boot File:/initrd.buffalo 4542614 bytes read <<stop_sound>> 4542614 bytes read <<stop_sound>> ## Booting image at 00100000 ... Image Name: Linux-2.6.16.16-arm1 Created: 2008-02-02 6:19:10 UTC Image Type: ARM Linux Kernel Image (uncompressed) Data Size: 1828584 Bytes = 1.7 MB Load Address: 00008000 Entry Point: 00008000 Verifying Checksum ... OK OK ## Loading Ramdisk Image at 00800000 ... Image Name: initrd Created: 2007-12-16 11:03:51 UTC Image Type: ARM Linux RAMDisk Image (gzip compressed) Data Size: 4542550 Bytes = 4.3 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Starting kernel ... arg:console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10 CONFIG_BUFFALO_PLATFORM CONFIG_BUFFALO_LINKSTATION_LSGL --- Uncompressing Linux...................................................................................................................... done, booting the kernel. Linux version 2.6.16.16-arm1 (root@test) (gcc version 4.1.2 20061115 (prerelease) (Debian 4.1.1-21)) #1 Sat Feb 2 14:11:04 JST 2008 CPU: ARM926EJ-Sid(wb) [41069260] revision 0 (ARMv5TEJ) Machine: MV-88fxx81 Using UBoot passing parameters structure Sys Clk = 200000000, Tclk = 166664740 - Warning - This LSP release was tested only with U-Boot release 1.7.3 Memory policy: ECC disabled, Data cache writeback CPU0: D VIVT write-back cache CPU0: I cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets CPU0: D cache: 32768 bytes, associativity 1, 32 byte lines, 1024 sets Built 1 zonelists Kernel command line: console=ttyS0,115200 root=/dev/sda2 rw initrd=0x00800040,15M panic=5 BOOTVER=1.10 PID hash table entries: 1024 (order: 10, 16384 bytes) Console: colour dummy device 80x30 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 128MB 0MB 0MB 0MB = 128MB total Memory: 110520KB available (3121K code, 532K data, 104K init) Mount-cache hash table entries: 512 CPU: Testing write buffer coherency: ok checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 15360K NET: Registered protocol family 16 FLASH boardId = 12 Flash bankwidth 1, base ff800000, size 400000 BUFFALO LS_GL FLASH size 4096[KB] Marvell Development Board (LSP Version 1.7.8_NAS)-- BUFFALO_BOARD_LS_GL Detected Tclk 166664740 and SysClk 200000000 Marvell USB EHCI Host controller #0: c16f5e00 Marvell USB EHCI Host controller #1: c16f5c00 pexBarOverlapDetect: winNum 2 overlap current 0 mvPexInit:Warning :Bar 2 size is illigal it will be disabled please check Pex and CPU windows configuration PCI: bus0: Fast back to back transfers enabled PCI: bus1: Fast back to back transfers enabled SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub use IDMA acceleration in copy to/from user buffers. used channels 2 and 3 Done. cesadev_init(c00112bc) mvCesaInit: sessions=640, queue=32, pSram=f0000000 Fast Floating Point Emulator V0.9 (c) Peter Teichmann. SGI XFS with no debug enabled Initializing Cryptographic API io scheduler noop registered io scheduler anticipatory registered (default) io scheduler deadline registered io scheduler cfq registered Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled serial8250: ttyS0 at MMIO 0x0 (irq = 3) is a 16550A serial8250: ttyS1 at MMIO 0x0 (irq = 4) is a 16550A RAMDISK driver initialized: 3 RAM disks of 16384K size 1024 blocksize loop: loaded (max 8 devices) Marvell Gigabit Ethernet Driver 'egiga': o Ethernet descriptors in DRAM o DRAM SW cache-coherency o Checksum offload enabled o Loading network interface ** egiga_init_module (0) 'eth0' Intergrated Sata device found scsi0 : Marvell SCSI to SATA adapter scsi1 : Marvell SCSI to SATA adapter ** BUFFALO Disable Command Queuing Function [0 1] ** Vendor: Maxtor Model: 6Y080L0 Rev: YAR4 Type: Direct-Access ANSI SCSI revision: 03 Linux IAL (ERROR) : retry command host=1, bus=1 SCpnt = c1437ba0 SCSI device sda: 160086528 512-byte hdwr sectors (81964 MB) sda: Write Protect is off SCSI device sda: drive cache: write back SCSI device sda: 160086528 512-byte hdwr sectors (81964 MB) sda: Write Protect is off SCSI device sda: drive cache: write back sda: sda1 sda2 sda4 < sda5 sda6 > sd 1:0:0:0: Attached scsi disk sda sd 1:0:0:0: Attached scsi generic sg0 type 0 physmap flash device: 400000 at ff800000 >jedec_probe Found: SST 39LF020 phys_mapped_flash: Found 1 x8 devices at 0x0 in 8-bit bank number of JEDEC chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. cmdlinepart partition parsing not available RedBoot partition parsing not available ehci_platform ehci_platform.4523: EHCI Platform Host Controller ehci_platform ehci_platform.4523: new USB bus registered, assigned bus number 1 ehci_platform ehci_platform.4523: irq 17, io mem 0x00000000 ehci_platform ehci_platform.4523: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected ehci_platform ehci_platform.16781: EHCI Platform Host Controller ehci_platform ehci_platform.16781: new USB bus registered, assigned bus number 2 ehci_platform ehci_platform.16781: irq 12, io mem 0x00000000 ehci_platform ehci_platform.16781: USB 0.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 1 port detected USB Universal Host Controller Interface driver v2.3 Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. mice: PS/2 mouse device common for all mice Kernel event proc (C) BUFFALO INC. V.1.00 installed. MICON ctrl (C) BUFFALO INC. V.1.00 installed. MICON V2 (C) BUFFALO INC. V.1.00 installed. NET: Registered protocol family 2 IP route cache hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 8192 (order: 3, 32768 bytes) TCP bind hash table entries: 8192 (order: 3, 32768 bytes) TCP: Hash tables configured (established 8192 bind 8192) TCP reno registered TCP bic registered NET: Registered protocol family 1 NET: Registered protocol family 17 RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). kjournald starting. Commit interval 5 seconds EXT3 FS on sda2, internal journal EXT3-fs: mounted filesystem with ordered data mode. VFS: Mounted root (ext3 filesystem). Trying to move old root to /initrd ... okay Freeing init memory: 104K INIT: version 2.86 booting Activating swap:swapon on /dev/sda5 Adding 248968k swap on /dev/sda5. Priority:-1 extents:1 across:248968k . Setting the system clock.. System Clock set. Local time: Sun Feb 3 20:12:25 JST 2008. Cleaning up ifupdown.... Loading device-mapper support. Will now check all file systems. fsck 1.40-WIP (14-Nov-2006) Checking all file systems. [/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -a -C0 /dev/sda1 /dev/sda1: clean, 18/100744 files, 32894/401409 blocks [/sbin/fsck.ext3 (1) -- /mnt] fsck.ext3 -a -C0 /dev/sda6 /dev/sda6: clean, 59414/9814016 files, 555209/19605316 blocks Done checking file systems. A log is being saved in /var/log/fsck/checkfs if that location is writable. Setting kernel variables...done. Will now mount local filesystems:mount: none already mounted or /dev/pts busy mount: according to mtab, devpts is already mounted on /dev/pts kjournald starting. Commit interval 5 seconds EXT3 FS on sda1, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on sda6, internal journal EXT3-fs: mounted filesystem with ordered data mode. failed! Will now activate swapfile swap:done. Cleaning /tmp...done. Cleaning /var/run...done. Cleaning /var/lock...done. Running 0dns-down to make sure resolv.conf is ok...done. Setting up networking.... * /etc/network/options is deprecated (see README.Debian of netbase). Setting up IP spoofing protection...done (rp_filter). Configuring network interfaces...Internet Software Consortium DHCP Client 2.0pl5 Copyright 1995, 1996, 1997, 1998, 1999 The Internet Software Consortium. All rights reserved. Please contribute if you find this software useful. For info, please visit http://www.isc.org/dhcp-contrib.html eth0: link down Listening on LPF/eth0/00:16:01:35:3e:a6 Sending on LPF/eth0/00:16:01:35:3e:a6 Sending on Socket/fallback/fallback-net DHCPREQUEST on eth0 to 255.255.255.255 port 67 eth0: link up<5>, full duplex<5>, speed 100 Mbps<5> DHCPREQUEST on eth0 to 255.255.255.255 port 67 DHCPACK from 192.168.0.254 bound to 192.168.0.72 -- renewal in 86400 seconds. done. Setting console screen modes and fonts. Initializing random number generator...done. Recovering nvi editor sessions...none found. INIT: Entering runlevel: 2 Starting system log daemon: syslogd. Starting kernel log daemon: klogd. Starting MTA: exim4. Starting internet superserver: inetd. Starting ftp server: proftpd - IPv6 getaddrinfo 'test.anabuki.dip.jp' error: Name or service not known . Starting deferred execution scheduler: atd. Starting periodic command scheduler: crond. Running local boot scripts (/etc/rc.local). Debian GNU/Linux 4.0 test ttyS0 test login: anabuki Password: Last login: Sun Feb 3 20:05:04 2008 from 192.168.0.60 on pts/0 Linux test 2.6.16.16-arm1 #1 Sat Feb 2 14:11:04 JST 2008 armv5tejl The programs included with the Debian GNU/Linux system are free software; the exact distribution terms for each program are described in the individual files in /usr/share/doc/*/copyright. Debian GNU/Linux comes with ABSOLUTELY NO WARRANTY, to the extent permitted by applicable law. anabuki@test:~$ su Password: |